# HMB log file
< 2019_07_30_h09:39:37 > Loading Configuration file ./config/default.cfg
< 2019_07_30_h09:39:37 > Encoder Resolution = 20.0000000000
< 2019_07_30_h09:39:37 > Print-Head Resolution type = dpi
< 2019_07_30_h09:39:37 > Print-Head Resolution = 1200.0000000000
< 2019_07_30_h09:39:37 > Encoder Source = 0
< 2019_07_30_h09:39:37 > Internal Encoder Frequency = 5000.0000000000
< 2019_07_30_h09:39:37 > Encoder Phase = 1
< 2019_07_30_h09:39:37 > Encoder Edge = 2
< 2019_07_30_h09:39:37 > Encoder Directionality = 0
< 2019_07_30_h09:39:37 > PD Source = 3
< 2019_07_30_h09:39:37 > PD Edge = 0
< 2019_07_30_h09:39:37 > Print-Mode = Continuous
< 2019_07_30_h09:39:37 > PD-Type = None
< 2019_07_30_h09:39:37 > Image Length = 0.0000000000 pixel
< 2019_07_30_h09:39:37 > Gap Length = 0.0000000000 pixel
< 2019_07_30_h09:39:37 > Print-Head Width = 0.0000000000 pixel
< 2019_07_30_h09:39:37 > Forward-Pass Pre-Print Buffer Length = 0.0000000000 pixel
< 2019_07_30_h09:39:37 > Swathe Length = 0.0000000000 pixel
< 2019_07_30_h09:39:37 > Reverse-Pass Offset = 0.0000000000 pixel
< 2019_07_30_h09:39:37 > Pre-Print Additional Movement = 0.0000000000 mm
< 2019_07_30_h09:39:37 > Daisy-Chain Enable = 1
< 2019_07_30_h09:39:37 > Daisy-Chain Position = 1
< 2019_07_30_h09:39:37 > Daisy-Chain Length = 1
< 2019_07_30_h09:39:37 > Configuration file loaded.
< 2019_07_30_h09:39:37 > Make sure to be connected to the EMB Server and press the button 'Apply' to configure the EMB
< 2019_07_30_h09:39:37 > Starting Remote-Server on port 6124
< 2019_07_30_h09:39:46 > ERROR: Unable to connect to the EMB-server on IP address 192.168.79.139
< 2019_07_30_h09:40:21 > Opened connection to IP 192.168.79.139, Port 6121
< 2019_07_30_h09:40:21 > show server.version
< 2019_07_30_h09:40:21 > hmb_remote_server version 1.10016.0.5356

< 2019_07_30_h09:40:21 > show fpm_ctrl.fw_info
< 2019_07_30_h09:40:21 > GIS-HMB Board - Firmware version is F003

< 2019_07_30_h09:40:23 > set diag.pd_watchdog_enable 0 0.1
< 2019_07_30_h09:40:23 > set diag.polling 7 200
< 2019_07_30_h09:42:49 > show print.force_all_zeros
< 2019_07_30_h09:42:49 > 0

< 2019_07_30_h09:43:05 > set pg.wh_wheel_corr 1 4827
< 2019_07_30_h09:43:05 > W&H - Wheel Correction Enabled
< 2019_07_30_h09:43:30 > <Detected-PD> Event-Number #1, Time = 500.092 s, Positition = 101.540000 mm (abs_pos = 20308)
< 2019_07_30_h09:43:37 > <Wheel-Correction> - Rotation Count = 1, Position Error = -2.000, Division-Ratio Correction = -0.00331500
< 2019_07_30_h09:43:37 > <Detected-PD> Event-Number #2, Time = 506.773 s, Positition = 198.080000 mm (abs_pos = 39616)
< 2019_07_30_h09:43:44 > <Wheel-Correction> - Rotation Count = 2, Position Error = 1.000, Division-Ratio Correction = -0.00000000
< 2019_07_30_h09:43:44 > <Detected-PD> Event-Number #3, Time = 513.464 s, Positition = 294.620000 mm (abs_pos = 58924)
< 2019_07_30_h09:43:46 > <Detected-PD> Event-Number #4, Time = 515.962 s, Positition = 391.160000 mm (abs_pos = 78232)
< 2019_07_30_h09:43:47 > <Wheel-Correction> - Rotation Count = 3, Position Error = 2.000, Division-Ratio Correction = 0.00248600
< 2019_07_30_h09:43:49 > <Wheel-Correction> - Rotation Count = 4, Position Error = -1.000, Division-Ratio Correction = -0.00082900
< 2019_07_30_h09:43:49 > <Detected-PD> Event-Number #5, Time = 518.668 s, Positition = 487.700000 mm (abs_pos = 97540)
< 2019_07_30_h09:43:51 > <Detected-PD> Event-Number #6, Time = 520.496 s, Positition = 584.240000 mm (abs_pos = 116848)
< 2019_07_30_h09:43:51 > <Wheel-Correction> - Rotation Count = 5, Position Error = 0.000, Division-Ratio Correction = -0.00000000
< 2019_07_30_h09:43:52 > <Detected-PD> Event-Number #7, Time = 522.121 s, Positition = 680.780000 mm (abs_pos = 136156)
< 2019_07_30_h09:43:53 > <Wheel-Correction> - Rotation Count = 6, Position Error = 0.000, Division-Ratio Correction = -0.00000000
< 2019_07_30_h09:43:54 > <Detected-PD> Event-Number #8, Time = 523.475 s, Positition = 777.320000 mm (abs_pos = 155464)
< 2019_07_30_h09:43:54 > <Wheel-Correction> - Rotation Count = 7, Position Error = 0.000, Division-Ratio Correction = -0.00000000
< 2019_07_30_h09:44:12 > <Detected-PD> Event-Number #9, Time = 542.085 s, Positition = 872.320000 mm (abs_pos = 174464)
< 2019_07_30_h09:44:14 > <Wheel-Correction> - Rotation Count = 8, Position Error = -1.000, Division-Ratio Correction = -0.51046200
< 2019_07_30_h09:44:15 > <Detected-PD> Event-Number #10, Time = 544.155 s, Positition = 967.320000 mm (abs_pos = 193464)
< 2019_07_30_h09:44:15 > <Wheel-Correction> - Rotation Count = 9, Position Error = -1.000, Division-Ratio Correction = -0.25688900
< 2019_07_30_h09:44:17 > <Wheel-Correction> - Rotation Count = 10, Position Error = 2.000, Division-Ratio Correction = -0.25274600
< 2019_07_30_h09:44:17 > <Detected-PD> Event-Number #11, Time = 546.342 s, Positition = 1062.320000 mm (abs_pos = 212464)
< 2019_07_30_h09:44:19 > <Detected-PD> Event-Number #12, Time = 548.990 s, Positition = 1157.320000 mm (abs_pos = 231464)
< 2019_07_30_h09:44:20 > <Wheel-Correction> - Rotation Count = 11, Position Error = -1.000, Division-Ratio Correction = -0.25606000
< 2019_07_30_h09:44:22 > <Detected-PD> Event-Number #13, Time = 551.806 s, Positition = 1252.320000 mm (abs_pos = 250464)
< 2019_07_30_h09:44:22 > <Wheel-Correction> - Rotation Count = 12, Position Error = 0.000, Division-Ratio Correction = -0.25523200
< 2019_07_30_h09:44:24 > <Detected-PD> Event-Number #14, Time = 553.494 s, Positition = 1347.320000 mm (abs_pos = 269464)
< 2019_07_30_h09:44:24 > <Wheel-Correction> - Rotation Count = 13, Position Error = 0.000, Division-Ratio Correction = -0.25523200
< 2019_07_30_h09:44:25 > <Wheel-Correction> - Rotation Count = 14, Position Error = 0.000, Division-Ratio Correction = -0.25523200
< 2019_07_30_h09:44:25 > <Detected-PD> Event-Number #15, Time = 554.990 s, Positition = 1442.320000 mm (abs_pos = 288464)
< 2019_07_30_h09:59:11 > set diag.polling 0 200
< 2019_07_30_h09:59:11 > set server.disconnect
< 2019_07_30_h09:59:11 > Closed connection to 192.168.79.139
< 2019_07_30_h09:59:11 > <Wheel-Correction> - Rotation Count = -1, Position Error = 0.000, Division-Ratio Correction = -1.00000000
< 2019_07_30_h09:59:43 > Closing EMB Console ...
