CORE-798 Fix Make EL GIP Library FPGA Vendor Independent.

Make uart variable bit length
This commit is contained in:
David Steele 2022-10-18 14:53:23 +01:00
commit b235c6041a

View file

@ -25,18 +25,20 @@
`timescale 1ns/1ps
module uart_1MBd_uart_txrd_4 #(
parameter OVERSAMPLE_RATE = 5'd16,
parameter ENABLE_CLOCK_DIVIDER = 6'd52
parameter ENABLE_CLOCK_DIVIDER = 6'd52,
parameter DW = 4'd8,
parameter TW = 4'd10
)
(
// Port Declarations
input wire clk,
output wire de_out,
output wire [7:0] rx_data_out,
output wire [DW-1:0] rx_data_out,
output wire rx_dv_out,
input wire rx_en_in,
input wire rx_in,
output wire rx_error_out,
input wire [7:0] tx_data_in,
input wire [DW-1:0] tx_data_in,
input wire tx_dv_in,
input wire tx_en_in,
output wire tx_out,
@ -46,7 +48,6 @@ module uart_1MBd_uart_txrd_4 #(
// Parameters
// Internal Declarations
localparam DATA_BITS = 4'd8;
localparam EDGE_DETECT_POSITION = OVERSAMPLE_RATE/2;
// RX State machine constants
@ -71,7 +72,7 @@ wire clk_en;
wire rx_neg_edge;
wire rx_bit_valid;
reg [2:0] rx_state = RX_IDLE;
reg [3:0] rx_bit_cnt = DATA_BITS - 4'd1;
reg [3:0] rx_bit_cnt = DW - 4'd1;
reg rx_receiving = 1'b0;
reg rx_done = 1'b0;
reg rx_error = 1'b0;
@ -81,10 +82,10 @@ wire tx_new_word;
wire tx_next_bit;
wire tx_last_bit;
wire tx_done;
reg [3:0] tx_bit_cnt = DATA_BITS + 4'd2;
reg [3:0] tx_bit_cnt = DW + 4'd2;
reg tx_ignore_idle = 1'b0;
reg [9:0] tx_data = 10'h3ff; // Extra bits allow easy addition of start bit to data.
reg [DW+1:0] tx_data = ~0; // Extra bits allow easy addition of start bit to data.
reg tx_rdy = 1'b1;
reg tx_busy = 1'b0;
@ -141,7 +142,7 @@ begin
if (~tx_busy | tx_next_bit) tx_bit_tmr <= (OVERSAMPLE_RATE-5'd1);
else if (clk_en) tx_bit_tmr <= tx_bit_tmr - 5'd1;
if (tx_new_word) tx_bit_cnt <= DATA_BITS + 4'd2;
if (tx_new_word) tx_bit_cnt <= DW + 4'd2;
else if (tx_next_bit) tx_bit_cnt <= tx_bit_cnt - 4'd1;
if (tx_new_word) tx_busy <= 1'b1; // This takes priority, to allow continuous transmission
@ -153,8 +154,8 @@ begin
else
begin
tx_bit_tmr <= (OVERSAMPLE_RATE-5'd1);
tx_bit_cnt <= DATA_BITS + 4'd2;
tx_data <= 10'h3ff;
tx_bit_cnt <= DW + 4'd2;
tx_data <= ~0;
tx_busy <= 1'b0;
tx_rdy <= 1'b1;
end
@ -207,7 +208,7 @@ begin
case (rx_state)
RX_GET_START : if (rx_neg_edge)
begin
rx_bit_cnt <= DATA_BITS- 4'd1; // Ensure correct number of bits are counted
rx_bit_cnt <= DW- 4'd1; // Ensure correct number of bits are counted
rx_receiving <= 1'b1;
rx_state <= RX_GET_DATA; // State transition
end