Vproc_n1/bfm/apbbfm.v
2024-10-09 13:45:44 +01:00

185 lines
No EOL
5.2 KiB
Verilog

// ====================================================================
//
// Verilog APB bus functional model (BFM) wrapper for VProc.
//
// Copyright (c) 2024 Simon Southwell.
//
// Implements minimal compliant initiator interface at 32-bits wide.
// Also has a vectored irq input.
//
// This file is part of VProc.
//
// VProc is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License, or
// (at your option) any later version.
//
// VProc is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with VProc. If not, see <http://www.gnu.org/licenses/>.
//
// ====================================================================
module apbbfm
# (parameter
ADDRWIDTH = 32, // For future proofing. Do not change.
DATAWIDTH = 32, // For future proofing. Do not change.
IRQWIDTH = 32, // Range 1 to 32
NODE = 0
)
(
input pclk,
input presetn,
// Master PSEL. Decode paddr externally for each individual completer
output pselx,
output [ADDRWIDTH-1:0] paddr,
output [DATAWIDTH-1:0] pwdata,
output pwrite,
output penable,
output [DATAWIDTH/8-1:0] pstrb,
output [2:0] pprot,
input [DATAWIDTH-1:0] prdata,
input pready,
input pslverr,
input [IRQWIDTH-1:0] irq
);
// -----------------------------------------
// Signals declarations for VProc
// -----------------------------------------
wire update;
wire rd;
wire [ADDRWIDTH-1:0] addr;
wire we;
wire [DATAWIDTH/8-1:0] be;
wire wrack;
wire [DATAWIDTH-1:0] dataout;
wire [DATAWIDTH-1:0] datain;
wire rdack;
reg [DATAWIDTH-1:0] prdata_int;
reg pready_int;
reg data_phase;
reg updateresp;
// -----------------------------------------
// Combinatorial logic
// -----------------------------------------
// Fixed protection status
assign pprot = 3'b010; // Normal, insecure and data access
// Pass through write enable, byte enables, address and output data directly from VProc
assign pwrite = we;
assign paddr = addr;
assign pwdata = dataout;
assign pstrb = be;
// Assert global PSEL when reading or writing
assign pselx = rd | we;
// Assert PENABLE if ot selected or in data phase
assign penable = ~pselx | data_phase;
// Input data directlay from PRDATA
assign datain = prdata_int;
// Acknowledge reads or writes when PREADY asserted
assign rdack = rd & pready_int;
assign wrack = we & pready_int;
// -----------------------------------------
// Initial block
// -----------------------------------------
initial
begin
updateresp = 1'b0;
end
// -----------------------------------------
// Synchronous process
// -----------------------------------------
always @(posedge pclk or negedge presetn)
begin
if (presetn == 1'b0)
begin
data_phase <= 1'b0;
end
else
begin
// Data phase is set on PSEL if no PREADY (address phase),
// and cleared again when PREADY asserted (data phase and data returned).
data_phase <= (data_phase | pselx) & ~(pselx & pready_int);
end
end
// For verilator, sample the inputs on the negative edge of the clock.
// All other simulators pass straight through.
`ifdef VERILATOR
always @(negedge pclk)
`else
always @(*)
`endif
begin
prdata_int <= prdata;
pready_int <= pready;
end
// -----------------------------------------
// Delta cycle process
// -----------------------------------------
always @(update)
begin
// Place any delta cycle processing logic before next line
updateresp <= ~updateresp;
end
// -----------------------------------------
// VProc instantiation
// -----------------------------------------
VProc
#(
.BURST_ADDR_INCR (4),
.INT_WIDTH (IRQWIDTH)
) vp
(
.Clk (pclk),
// Bus
.Addr (addr),
.DataOut (dataout),
.WE (we),
.BE (be),
.WRAck (wrack),
.DataIn (datain),
.RD (rd),
.RDAck (rdack),
// Interrupts
.Interrupt (irq),
// Delta cycle control
.Update (update),
.UpdateResponse (updateresp),
.Node (NODE[3:0])
);
endmodule