bladeRF USB 3.0 Superspeed Software Defined Radio Source Code http://nuand.com
  • C 45.8%
  • VHDL 21%
  • Verilog 15.8%
  • Tcl 3.8%
  • MATLAB 3.2%
  • Other 10.3%
Find a file
Robert Ghilduta 552d779567 linux driver: add support for writing to the LMS, Si5388, and the VCTCXO
This commit adds the ioctls necessary to configure the LMS, Si5338, and VCTCXO.
The FX3's second endpoint is configured to receive and transmit things over
UART. At the other end of the UART is the Nios II core in the FPGA. The Nios
core simply parses the read or write operation and sends it to the appropriate
device.

NB: At least a 16byte URB has to be sent to the FX3 for it to send data on UART
due to a minimum buffer count enforced by the GPIF's DMA controller.

The UART packet format is as follows:
   Byte 0) "Magic" byte is 'N'

   Byte 1) Indicates the direction and intended device of each subsequent
           operation. Count is number of struct uart_cmd data structures that
           will be transferred.
   //  | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |$
   //  |  dir  |  dev  |     cnt       |$

   Byte 2..N) The following byte pairs are struct uart_cmd, which consist of
           addresses and values;
   struct uart_cmd {$
       unsigned char addr;$
       unsigned char data;$
   };$

As an example, if you are looking to write 0xC0 to register 0x30 on the Si5338,
the UART packet you would have to send would have to look like this:
   Byte 0) 'N'
   Byte 1) UART_PKT_MODE_DIR_WRITE | UART_PKT_DEV_SI5338 | 0x01;$
   Byte 2) 0x30$
   Byte 3) 0xC0$

Before sending this packet to the second endpoint, the packet would have to be
zero padded to the nearest 16 byte boundary.
2013-06-02 23:57:36 -07:00
common linux driver: add support for writing to the LMS, Si5388, and the VCTCXO 2013-06-02 23:57:36 -07:00
fx3_firmware new USB ID 2013-06-02 23:57:35 -07:00
hdl hdl: add Si5338 support to the nios core 2013-06-02 23:57:34 -07:00
linux linux driver: add support for writing to the LMS, Si5388, and the VCTCXO 2013-06-02 23:57:36 -07:00
COPYING FSK bridge example 2013-02-18 20:11:39 -08:00
README FSK bridge example 2013-02-18 20:11:39 -08:00

This README details how to build the FSK bridge example

To build and run the FSK bridge rea
1) Open existing hdl/quartus/bladerf.qsf project in Quartus
	a) Generate the Nios core
		i) Tools -> QSys -> File -> Open -> navigate to ./hdl/fpga/ip/altera/nios_system/nios_system.qsys
		ii) After opening qsys file, go to Generation tab, click the "Generate" button
	b) Compile the embedded Nios image
		i) Tools -> Nios II Software Build Tools for Eclipse
			I)   File -> Import -> General -> Existing Projects into Workspace -> Next
				-> Browse to checkout root directory -> check both lms_spi_controller and lms_spi_controller_bsp
				-> Finish
			II)  right click lms_spi_controller_bsp -> NIOS II -> Generate BSP
			III) right click lms_spi_controller -> Build
			IV)  right click lms_spi_controller -> Make Targets -> Build... -> select mem_init_generate -> Build
	c) Synthesize FPGA image
		i) Processing -> Start Compilation

2) Compile driver and user mode applications
	a) cd linux/kernel ; make ; inmod bladeRF.ko
	b) cd ../apps; make
	c) To program the fpga execute ./simple_load c4images/blink.rbf
		i) Load bladerf.rbf from the quartus output_files directory

3) Use bladeRF as an FSK bridge!