The CLI now supports flashing the FX3 and loading the FPGA from the command line and through the interactive console. To flash the firmware from the command line: ./bin/bladerf -b -f ./path/to/img -d /dev/bladerf1 To load the firmware from the command line: ./bin/bladerf -b -l ./path/to/rbf -d /dev/bladerf1 To flash/load interactively either run with -d /dev/bladerf1, or use the open command to attach to a device: bladeRF> open /dev/bladerf1 To flash the firmware interactively: bladeRF> load fx3 ./path/to/img To load the FPGA interactively: bladeRF> load fpga ./path/to/rbf Note that a power-on-reset is currently required in between flashing firmware and loading the FPGA. Various commands have been stubbed out for the time being. A TODO list has been created to keep track of desired functionality. The simple_load and upgrade_firmware programs have been removed, as they are no longer needed.
71 lines
1.4 KiB
Text
71 lines
1.4 KiB
Text
################
|
|
# CLI Commands #
|
|
################
|
|
|
|
= Low level commands =
|
|
peek <lms|dac|si> <address>
|
|
poke <lms|dac|si> <address> <data>
|
|
|
|
= Higher level commands =
|
|
set <value> <options>+
|
|
frequency <rx,tx> <value>
|
|
rxvga1 <value>
|
|
rxvga2 <value>
|
|
txvga1 <value>
|
|
txvga2 <value>
|
|
pa <1,2,both> <on,off>
|
|
loopback <bb,rf>
|
|
bandwidth <tx,rx> <bw>
|
|
samplerate <tx,rx,both> <freq in Hz>
|
|
samplerate <tx,rx,both> <integer in Hz> <num> <denom>
|
|
trimdac <value: 0 to 65535>
|
|
mimo <master|slave>
|
|
refclk <enable|disable> <frequency if enable only>
|
|
pps <enable|disable>
|
|
|
|
print
|
|
config <-- basically an overview of everything
|
|
frequency
|
|
rxvga1
|
|
rxvga2
|
|
txvga1
|
|
txvga2
|
|
pa
|
|
loopback
|
|
bandwidth
|
|
samplerate
|
|
trimdac
|
|
lmsdump
|
|
mimo
|
|
refclk
|
|
pps
|
|
|
|
load <fpga|fx3> <filename>
|
|
|
|
version
|
|
fx3: <version from header>
|
|
fpga: <version register>
|
|
bladerf: <serial #, revision #>
|
|
|
|
tx <filename> [--repeat]
|
|
rx <filename> <# samples>
|
|
|
|
|
|
|
|
################
|
|
# Misc #
|
|
################
|
|
|
|
Add "Notes:" section to help text to explain items in more detail.
|
|
|
|
Programming FX3/FPGA should not require -d if there's only one
|
|
device. Implicity used any attached device if there's just one.
|
|
Otherwise, require -d and complain, exit.
|
|
|
|
|
|
################
|
|
# Programming #
|
|
################
|
|
|
|
Add a --all option to allow us to flash all attached devices with specified
|
|
firmware?
|