bladeRF USB 3.0 Superspeed Software Defined Radio Source Code http://nuand.com
  • C 45.8%
  • VHDL 21%
  • Verilog 15.8%
  • Tcl 3.8%
  • MATLAB 3.2%
  • Other 10.3%
Find a file
Rey Tucker df07dd941a
host: libbladeRF/bladerf2: cache factory trimdac value, preserve trimdac disable state (#582)
Fixes a lockup/crashy bug where bladerf2_get_vctcxo_trim would cause active RX/TX streams to fail. Also ensures that "set trimdac" won't inadvertently re-enable the trim DAC if it is disabled (e.g. because the PLL is enabled).

* host: libbladeRF/bladerf2: cache factory trimdac value

bladerf2_get_vctcxo_trim called spi_flash_rad_vctcxo_trim, which causes
an USB mode change which is incompatible with active sample streaming.
This would cause active RX/TX to fail if someone used "set trimdac" or
even "print".

We now cache the value during initialization, and return the cached
value if it is requested later on.

* host: libbladeRF/bladerf2: preserve trimdac disable state

If bladerf2_trim_dac_write is called with a new value, while the trim
DAC is disabled, make sure we do not inadvertently re-enable the trim
DAC.  Save the new value in the board_data struct for later use by
bladerf2_set_trim_dac_enable.
2018-08-23 17:06:58 -04:00
debian debian: add changelog entry for 2018.08-rc2 2018-08-16 19:56:02 -04:00
doc doc: update test_checklist.md for bladeRF micro (#30) 2018-05-22 12:58:21 -04:00
firmware_common firmware_common: add bladerf2 usb pid 2017-12-21 12:54:55 -05:00
fpga_common fpga_common: fix overrun in 16x64 NIOS II packet packing 2017-12-21 12:54:57 -05:00
fx3_firmware fx3_firmware: bump version to 2.2.0 2018-06-19 00:38:37 -04:00
hdl hdl: update changelog, set version 0.7.3 2018-08-07 15:25:25 -04:00
host host: libbladeRF/bladerf2: cache factory trimdac value, preserve trimdac disable state (#582) 2018-08-23 17:06:58 -04:00
legal legal: add AGPLv3, mention FPGA IP licenses (#38) 2018-05-23 12:15:00 -04:00
.clang-format clang-format: minor tweak for brackets on lists 2017-12-21 12:55:09 -05:00
.gitignore gitignore: Add cscope.files and cscope.out 2018-05-22 13:00:21 -04:00
CHANGELOG bladeRF 2018.03-alpha1 2018-03-26 16:30:42 -04:00
CMakeLists.txt fx3_firmware: Use CMake for project configuration and Makefile generation 2016-04-06 16:06:06 -04:00
CONTRIBUTORS CONTRIBUTORS: self-updating 2017-08-02 18:06:21 -04:00
COPYING legal: add AGPLv3, mention FPGA IP licenses (#38) 2018-05-23 12:15:00 -04:00
README.md Update CMake options in READMEs (#285) 2014-07-27 13:32:49 -04:00

bladeRF Source

This repository contains all the source code required to program and interact with a bladeRF platform, including firmware for the Cypress FX3 USB controller, HDL for the Altera Cyclone IV FPGA, and C code for the host side libraries, drivers, and utilities. The source is organized as follows:

Directory Description
firmware_common Source and header files common between firmware and host software
fx3_firmware Firmware for the Cypress FX3 USB controller
hdl All HDL code associated with the Cyclone IV FPGA
host Host-side libraries, drivers, utilities and samples

Quick Start

  1. Clone this repository via: git clone https://github.com/Nuand/bladeRF.git
  2. Fetch the latest pre-built bladeRF FPGA image. See the README.md in the hdl directory for more information.
  3. Fetch the latest pre-built bladeRF firmware image. See the README.md in the fx3_firmware directory for more information.
  4. Follow the instructions in the host directory to build and install libbladeRF and the bladeRF-cli utility.
  5. Attach the bladeRF board to your fastest USB port.
  6. You should now be able to see your device in the list output via bladeRF-cli -p
  7. You can view additional information about the device via bladeRF-cli -e info -e version.
  8. If any warnings indicate that a firmware update is needed, run:bladeRF-cli -f <firmware_file>.
  • If you ever find the device booting into the FX3 bootloader (e.g., if you unplug the device in the middle of a firmware upgrade), see the recovery command in bladeRF-cli for additional details.
  1. See the overview of the bladeRF-cli for more information about loading the FPGA and using the command line interface tool

For more information, see the bladeRF wiki.

Build Variables

Below are global options to choose which parts of the bladeRF project should be built from the top level. Please see the fx3_firmware and host subdirectories for more specific options.

Option Description
-DENABLE_FX3_BUILD=<ON/OFF> Enables building the FX3 firmware. Default: OFF
-DENABLE_HOST_BUILD=<ON/OFF> Enables building the host library and utilities overall. Default: ON