Offset in core for bus CSR : 0x00020000
| fpm_ctrl_7 | This block is the fire pulse manager control | ||||||
|---|---|---|---|---|---|---|---|
| Register Name | Byte Addr Offset | Field | Bits | Type | subtype | Reset | Description |
| CSR_FPM_CTRL_7_IP_ID | 0x0 | 32 | Unique ID for this IP block | ||||
| IP_NUMBER | 7:0 | c | 0x14 | IP identifier number | |||
| MFR_NUMBER | 15:8 | c | 0xFF | Manufacturer number | |||
| RESERVED | 31:16 | rsv | 0 | Reserved bits | |||
| CSR_FPM_CTRL_7_IP_VER | 0x4 | 32 | IP Version | ||||
| MINOR_NUMBER | 7:0 | c | 0x05 | Minor number | |||
| MAJOR_NUMBER | 15:8 | c | 0x07 | Major number | |||
| RESERVED | 31:16 | rsv | 0 | Reserved bits | |||
| CSR_FPM_CTRL_7_FPM_CONFIG | 0x8 | 10 | Configuration values for the FPM | ||||
| CH_NUM | 3:0 | r | 0 | Number of channels | |||
| SEB_EPD_LOGIC_PRESENT | 4 | r | 0 | 0 => SEB-EPD logic not present, 1 => SEB-EPD logic present | |||
| EPD_DIAGNOSTIC_PRESENT | 5 | r | 0 | 0 => EPD diagnostic block not present, 1 => EPD diagnostic block present. Encoder Product Detect Diagnostics. Previously called smb_diags | |||
| EVENT_LOGGER_PRESENT | 6 | r | 0 | 0 => Event Logger block not present, 1 => Event Logger block present | |||
| DELAY_EQUALIZATION_ENABLE | 7 | r | 0 | 0 => No support for delay equalization, 1 => Support for delay equalization | |||
| TOF_COMP_ENABLE | 8 | r | 0 | 0 => No support for Time-of-Flight compensation, 1 => Support for Time-of-Flight compensation | |||
| PIXEL_PITCH_CORR_ENABLE | 9 | r | 0 | 0 => No support for pixel-pitch correction, 1 => Support for pixel-pitch correction | |||
| CSR_FPM_CTRL_7_FPM_INIT_START | 0xc | 1 | w | 0 | Start the fpm_init procedure | ||
| CSR_FPM_CTRL_7_FPM_INIT_DONE | 0x10 | 1 | r | 0 | fpm_init completed flag | ||
| CSR_FPM_CTRL_7_SIGNAL_SELECTION | 0x14 | 6 | Controls signal selection | ||||
| FIRE_PULSE_SEL | 0 | w | 0x0 | 0 => Use External fire pulses, 1 => Use FPM fire pulses | |||
| ENC_PD_EMUL_EN | 1 | w | 0x0 | 0 => Use POF RX, 1 => Use internal enc/PD emulator | |||
| SEB_EPD_EN | 2 | w | 0x0 | 1 => Enable SEB-EPD interface, 0 => Use POF based interface | |||
| SEB_EPD_LINKOUT_SEL | 3 | w | 0x0 | 0 => SEB_EPD_LINK_OUT is driven by the POF-Tx output, 0 => SEB_EPD_LINK_OUT is driven by the Drop-Watch output | |||
| PRINT_START_OVERRIDE | 5:4 | w | 0x0 | 0- => no override. 10 => override to zero (stop print). 11 => override to one (start print). output of FPM and value for pof_tx | |||
| CSR_FPM_CTRL_7_POF_RECEIVER_CONTROL | 0x18 | 9 | Controls POF receiver | ||||
| POF_RX_ENABLE | 0 | w | 0x0 | 0 => Disable POF RX, 1 => Enable POF RX | |||
| UART_REGENERATION_BYPASS | 1 | w | 0x0 | 0 => Use UART Regeneration, 1 => Bypass UART Regeneration | |||
| CLEAR_MAX | 2 | w | 0x0 | 0 => Disabled, 1 => Load the current value of Absolute Position as new maximum | |||
| CLEAR_MIN | 3 | w | 0x0 | 0 => Disabled, 1 => Load the current value of Absolute Position as new miniumum | |||
| UART_RX_DIV | 7:4 | w | 0x4 | Defines the number of 200 MHz clock cycles per UART data bit | |||
| POF_PROTOCOL_VERSION | 8 | w | 0 | 0 => Support POF protocol version 0, 1 => Support POF protocol version 1 (allows print_start message) | |||
| CSR_FPM_CTRL_7_MONITORING_POINT_SELECTION | 0x1c | 16 | Selects monitoring points for external header | ||||
| MP0 | 3:0 | w | 0x0 | Selects first monitoring point | |||
| MP1 | 7:4 | w | 0x0 | Selects second monitoring point | |||
| MP2 | 11:8 | w | 0x0 | Selects third monitoring point | |||
| MP3 | 15:12 | w | 0x0 | Selects fourth monitoring point | |||
| CSR_FPM_CTRL_7_COARSE_TIME_INIT | 0x20 | 32 | w | 0x00000000 | Defines coarse time counter value | ||
| CSR_FPM_CTRL_7_FINE_TIME_INIT | 0x24 | 29 | Fine time counter value/Load counter enable | ||||
| FINE_TIME_INIT | 27:0 | w | 0x0000000 | Defines fine time counter value | |||
| TIME_LOAD_EN | 28 | w | 0x0 | Writting 1 loads the coarse and fine time counters | |||
| CSR_FPM_CTRL_7_FINE_TIME_STATUS | 0x28 | 28 | r | 0x0000000 | Current fine time counter value | ||
| CSR_FPM_CTRL_7_COARSE_TIME_STATUS | 0x2c | 32 | r | 0x00000000 | Current coarse time counter value | ||
| CSR_FPM_CTRL_7_POF_RX_STATUS | 0x30 | 32 | Status of POF receiver | ||||
| PARITY_BIT_ERROR_COUNT | 15:0 | r | 0x0000 | Counts number of parity errors | |||
| SKIPPED_POSITION_ERROR_COUNT | 31:16 | r | 0x0000 | Counts position skipped type errors | |||
| CSR_FPM_CTRL_7_POF_RX_CONTROL_W | 0x34 | 10 | POF receiver error control | ||||
| ERROR_RATE_THRES | 7:0 | w | 0x0A | Defines RX error rate threshold | |||
| RX_WATCHDOG_EN | 8 | w | 0x1 | 0 => Disable RX watchdog, 1 => Enable RX Watchdog | |||
| RX_WATCHDOG_CLR | 9 | w | 0x0 | 0 => RX watchdog counter running, 1 => Clear RX watchdog counter | |||
| CSR_FPM_CTRL_7_POF_RX_CONTROL_R | 0x38 | 3 | POF receiver error status | ||||
| RX_WATCHDOG | 0 | r | 0x0 | 0 => RX watchdog not triggered, 1 => RX watchdog triggered | |||
| RX_ERROR_FLAG | 1 | r | 0x0 | 0 => Error rate below threshold, 1 => Error rate above threshold | |||
| PRINT_START_RECEIVED | 2 | r | 0x0 | print_start as received over pof. (for protocol zero, will be fixed at '1') | |||
| CSR_FPM_CTRL_7_FPM_INTERRUPT | 0x3c | 12 | Interrupt control | ||||
| IRQ_EN | 0 | w | 0x0 | 0 => Disable IRQ, 1 => Enable IRQ | |||
| RESERVED1 | 3:1 | rsv | 0 | Reserved | |||
| IRQ_CLR | 4 | w | 0x0 | 0 => Don't clear pending IRQ, 1 => Clear pending IRQ | |||
| RESERVED2 | 7:5 | rsv | 0 | Reserved | |||
| IRQ_MASK | 8 | w | 0x0 | 0 => IRQ not masked, 1 => IRQ masked | |||
| RESERVED3 | 11:9 | rsv | 0 | Reserved | |||
| CSR_FPM_CTRL_7_IRQ_STATUS | 0x40 | 1 | r | 0x0 | 0 => IRQ not active, 1 => IRQ active | ||
| CSR_FPM_CTRL_7_PD_CNT | 0x44 | 16 | r | 0x0 | PD count, at the Pulse-Generator input | ||
| CSR_FPM_CTRL_7_DROP_WATCH_CONFIG | 0x48 | 32 | Drop-Watch configuration | ||||
| DW_SRC | 3:0 | w | 0x0 | Select the source channel for the drop-watch | |||
| RESERVED | 15:4 | rsv | 0 | Reserved | |||
| DW_PULSE_WIDTH | 31:16 | w | 0x000A | Drop-Watch pulse width, expressed as clock cycles @100MHz | |||
| CSR_FPM_CTRL_7_SEB_EPD_LED_STATUS | 0x4c | 12 | SEB-EPD LED status | ||||
| LED_PD_G | 0 | r | 0x0 | LED PD Green | |||
| LED_PD_Y | 1 | r | 0x0 | LED PD Yellow | |||
| LED_PD_R | 2 | r | 0x0 | LED PD Red | |||
| LED_ENC_P1_G | 3 | r | 0x0 | LED Encoder-Phase-1 Green | |||
| LED_ENC_P1_Y | 4 | r | 0x0 | LED Encoder-Phase-1 Yellow | |||
| LED_ENC_P1_R | 5 | r | 0x0 | LED Encoder-Phase-1 Red | |||
| LED_ENC_P2_G | 6 | r | 0x0 | LED Encoder-Phase-2 Green | |||
| LED_ENC_P2_Y | 7 | r | 0x0 | LED Encoder-Phase-2 Yellow | |||
| LED_ENC_P2_R | 8 | r | 0x0 | LED Encoder-Phase-2 Red | |||
| LED_POF_IN_G | 9 | r | 0x0 | LED POF-In Green | |||
| LED_POF_IN_Y | 10 | r | 0x0 | LED POF-In Yellow | |||
| LED_POF_IN_R | 11 | r | 0x0 | LED POF-In Red | |||
Register/field type key:
| Type | Description |
|---|---|
| c | Constant, with value defined by "reset" attribute |
| rsv | Same as constant, except no reset value and always 0. Can be mixed with write types. |
| w | Write register (and read—no write only type). Register defined in register block and reset to "reset" attribute value. Split into fields (if applicable) for signalling and output, where attribute associated with fields, not register. |
| wp | Write with pulse. Register is not declared in block, but write bus split into fields as output port signals, and a pulse generated on write to register address. Register reads back 0. The "reset" attribute is for documentation only, as set externally. |
| w0 | Same as w, but auto-clears to 0 (and thus always reads as 0). At output port, signal will go high for one cycle when bit is written with a 1 (no effect if written to a 0). No "reset" attribute, as must always be 0. |
| r | Read only value. Input ports generated for each field (where applicable), and concatenated on returned read data bus. |
| rp | Similar to r, but a pulse generated on a read access to the register address to allow peripheral logic to update value. The "reset" attribute is for documentation only, as set externally. |
| rwp | Similar to wp, but also generates a (separate) pulse on a read access to the register |
| bitdef | Defines the bits used in the read, set, clear registers |
| Subype | Description |
| unsigned | Register/field is specified as an unsigned value. |
| signed | Register/field is specified as a signed value. |
| <blank> | Register/field sign status is not explicitly defined and defaults to unsigned. |
This is the control registers for the Fire Pulse Manager. this link. The Fire Pulse Manager produces fire-request strobe signals to trigger the print_units to load and fire the printhead (or sub-head). It does so based on either received UART messages over Plastic Optic Fibre (POF) if using the SEB-PDW, or from encoder/PD inputs if using the SEB-EPD. Full details on confluence at this link
Copyright © 2024 Global Inkjet Systems. Generated by gen_htm.py —2024-10-30 09:43