gis_logo.png

Datasheet for the PULSE_GENERATOR_5 GIS Soft IP Embedded Logic

Register Definitions

pulse_generator_5 Generate Fire-Requests, based on the absolute position and PD inputs
Register Name Byte Addr Offset Field Bits Type subtype Reset Description
CSR_PULSE_GENERATOR_5_IP_ID 0x0 32 Unique ID for this IP block
IP_NUMBER 7:0 c 0x13 IP identifier number
MFR_NUMBER 15:8 c 0xFF Manufacturer number
RESERVED 31:16 rsv 0 Reserved bits
CSR_PULSE_GENERATOR_5_IP_VER 0x4 32 IP Version
MINOR_NUMBER 7:0 c 0x03 Minor number
MAJOR_NUMBER 15:8 c 0x05 Major number
RESERVED 31:16 rsv 0 Reserved bits
CSR_PULSE_GENERATOR_5_PULSE_GEN_CONTROL_W 0x8 20
ENABLE 0 w 0x0 Pulse-Generator Enable
BYPASS_CHANNEL_CONTROLLER 1 w 0x0 By-Pass Ch-Ctrl (=> Fractional Divider only)
RESERVED_0 2 rsv 0
BYPASS_DELAY_EQUALIZER 3 w 0x0 Bypass Delay Equalization
SW_CONTROL_DP_DIR 4 w 0x0 Dual-Phase Direction, when Ch-Ctrl is bypassed
RESERVED_1 10:5 rsv 0
WH_APPLY_CORR_EN 11 w 0x0 Enable WH wheel correction
PP_APPLY_CORR_EN 12 w 0x0 Enable Pixel-Pitch Correction
TOF_COMP_ENABLE 13 w 0x0 Enable Time-of-Flight Compensation
RESERVED_2 15:14 rsv 0
ENABLE_OUTPUT 16 w 0x0 Enable fire-request output
TRIGGER_ABORT_FIRE 17 w 0x0 Abort pending request of fire-request issued by Ch-Ctrl
RESET_DIAG_REGS 18 w 0x0 Reset the local PD and Fire-Request counters
CLR_PD_QUEUE 19 w0 0x0 Clear PD Queue
CSR_PULSE_GENERATOR_5_PULSE_GEN_CONTROL_R 0xc 15
RESERVED_0 4:0 rsv 0
PD_QUEUE_ERROR_FLAG 5 r 0x0 PD Queue Overflow Error
DELAY_EQUALIZER_ERROR_FLAG 6 r 0x0 Delay Equalizer Overflow Error
RESERVED_1 7 rsv 0
CH_MASK_STATUS 8 r 0x0 ch_mask status
FIRE_ENABLE_STATUS 9 r 0x0 fire enable status
DUAL_PHASE_DIRECTIONALITY_SELECT_STATUS 10 r 0x0 Dual-Phase Direction status
RESERVED_2 13:11 rsv 0
TOF_SAT_FLAG 14 r 0x0 Asserted when the current encoder velocity value falls outside of the range covered by the ToF compensation LUT. Velocity saturation is therefore applied.
CSR_PULSE_GENERATOR_5_PD_OFFSET_DIR_0 0x10 32 w 0x00 PD Offset for DIR-0
CSR_PULSE_GENERATOR_5_PD_OFFSET_DIR_1 0x14 32 w 0x00 PD Offset for DIR-1
CSR_PULSE_GENERATOR_5_CHANNEL_DELAY 0x18 16 w 0x00 Channel Delay (Delay Equalization)
CSR_PULSE_GENERATOR_5_CHANNEL_CONTROLLER_CONTROL_W 0x1c 19
START_SEQ_TRIGGER 0 w0 0x0 Ch-Ctrl Sequencer Start-Request
RESERVED0 7:1 rsv 0
SEQUENCER_START_ADDRESS 15:8 w 0x0 Ch-Ctrl Sequencer Start-Address
EVENT_FIFO_RESET 16 w0 0 Reset the event Fifo. Should have it's own register but run out of addresses and difficult to add more range. Generic sequencer starts at 32. Auto clears to zero
EVENT_FIFO_RD_POP 17 w0 0 Pop one value from the event FIFO. Auto clears to zero
MISSED_PD_COUNT_RESET 18 w0 0 Write set to reset the missed_pd_count. Auto clears to zero
CSR_PULSE_GENERATOR_5_CHANNEL_CONTROLLER_CONTROL_R 0x20 12
RESERVED0 0 rsv 0
BUSY 1 r 0x0 Ch-Ctrl Sequencer Busy
RESERVED1 3:2 rsv 0
MISSED_PD_COUNT 11:4 r 0x0 Number of PDs missed by the FPM Pulse Gen Sequencer
CSR_PULSE_GENERATOR_5_FRACTIONAL_DIVIDER_CONTROL 0x24 3 Fractional Divider Control Register
ENABLE 0 w 0x0 Fractional Divider Enable
UDP_MAX_POS 1 w 0x0 Clear the encoder jitter for DIR-0
UDP_MIN_POS 2 w 0x0 Clear the encoder jitter for DIR-1
CSR_PULSE_GENERATOR_5_DIVIDER_RATIO_INT 0x28 10 w 0x00 Integer part of the Division ratio
CSR_PULSE_GENERATOR_5_DIVIDER_RATIO_FRACTION 0x2c 24 w 0x00 Fractional part of the Division ratio
CSR_PULSE_GENERATOR_5_SUBPIXEL_PHASE_NUM 0x30 6 w 0x01 Number of sub-pixel phases to be generated
CSR_PULSE_GENERATOR_5_ABS_POSITION_MAX 0x34 32 r signed 0x00 Absolute Position Maximum
CSR_PULSE_GENERATOR_5_ABS_POSITION_MIN 0x38 32 r signed 0x00 Absolute Position Minimum
CSR_PULSE_GENERATOR_5_ABS_POSITION 0x3c 32 r signed 0x00 Current Absolute Position
CSR_PULSE_GENERATOR_5_PD_COUNTER 0x40 16 r 0x00 PD counter
CSR_PULSE_GENERATOR_5_FIRE_REQ_COUNTER 0x44 24 r 0x00 Fire-Request counter
CSR_PULSE_GENERATOR_5_ENC_SPEED_MEAS_WINDOW 0x48 20 w 0x0C350 Encoder speed measurement window length [clock cycles @100MHz]
CSR_PULSE_GENERATOR_5_ENC_SPEED 0x4c 20 r signed 0x0 Encoder Velocity: balance between positive and negative encoder steps over the measurement window
CSR_PULSE_GENERATOR_5_TOF_COMPENSATION_W 0x50 32 Time-of-Flight Compensation
ENC_SPEED_NORM 15:0 w 0x0100 Encoder Speed Normalization factor: allow to match the encoder-speed range to the address bus width of the ToF Compensation LUT. With the default value (256), an encoder-speed measurement equal to k selects LUT address k)
RESERVED0 31:16 rsv 0
CSR_PULSE_GENERATOR_5_TOF_COMPENSATION_R 0x54 32 Time-of-Flight Compensation
RESERVED0 15:0 rsv 0
TOF_LUT_COMP 31:16 r 0x0 Current value of the Time-of-Flight compensation
CSR_PULSE_GENERATOR_5_PIXEL_PITCH_CORR_STRIPE_NUM 0x58 24 w 0x00 Number of stripes to be considered for pixel pitch correction: corresponds to the number of pixels composing the label, head width included)
CSR_PULSE_GENERATOR_5_PIXEL_PITCH_POS_ERR_2_CORR 0x5c 32 w 0x00 Static value used by the logic to compute pixel-pitch correction: need to be set to the number of 2^32/stripe_num, where stripe_num is the value programmed in pixel_pitch_corr_stripe_num
CSR_PULSE_GENERATOR_5_PIXEL_PITCH_SKIP_CORR_THRES 0x60 24 w 0x400000 Alignment error threshold causing a correction to be skipped, expressed in encoder steps (24-bits integer)
CSR_PULSE_GENERATOR_5_PIXEL_PITCH_LOOP_FILTER_CORR 0x64 32 Loop filter coefficient for pixel-pitch correction
DELTA_ERROR_COEFF 15:0 w 0x0100 Loop Filter delta-error coefficient
TOT_ERROR_COEFF 31:16 w 0x0100 Loop Filter tot-error coefficient
CSR_PULSE_GENERATOR_5_PIXEL_PITCH_POS_ERR_CURR 0x68 32 r signed 0x00 Pixel-pitch misalignment measured on the last rotation [encoder steps], represented as signed, fixed point with 24-bits integer part and 8-bits mantissa
CSR_PULSE_GENERATOR_5_PIXEL_PITCH_POS_ERR_MAX 0x6c 32 r signed 0x00 Maximum recorded value of pixel-pitch misalignment [encoder steps], represented as signed, fixed point with 24-bits integer part and 8-bits mantissa
CSR_PULSE_GENERATOR_5_PIXEL_PITCH_POS_ERR_MIN 0x70 32 r signed 0x00 Minimum recorded value of pixel-pitch misalignment [encoder steps], represented as signed, fixed point with 24-bits integer part and 8-bits mantissa
CSR_PULSE_GENERATOR_5_PIXEL_PITCH_DIV_RATIO_CORR 0x74 32 r signed 0x00 Division-Ratio Correction (32-LSBs)
CSR_PULSE_GENERATOR_5_PIXEL_PITCH_CORR_CNT 0x78 16 r 0x00 Pixel-pitch corrections count
CSR_PULSE_GENERATOR_5_EVENT_FIFO_RD_STATUS 0x7c 24 Status and data readback for the Event FIFO
DATA 7:0 r 0 Pulse Gen Sequencer writes an ID into the FIFO to indicate job progess. This is the read port value
RESERVED0 11:8 rsv 0
UNDERRUN 12 r 0 Event FIFO read while Empty
OVERRUN 13 r 0 Event FIFO written while Full
FULL 14 r 0 Event FIFO Full
EMPTY 15 r 0 Event FIFO empty
RD_COUNT 23:16 r 0 Number of entries in the event FIFO (0-255)

Register/field type key:

TypeDescription
cConstant, with value defined by "reset" attribute
rsvSame as constant, except no reset value and always 0. Can be mixed with write types.
wWrite register (and read—no write only type). Register defined in register block and reset to "reset" attribute value. Split into fields (if applicable) for signalling and output, where attribute associated with fields, not register.
wpWrite with pulse. Register is not declared in block, but write bus split into fields as output port signals, and a pulse generated on write to register address. Register reads back 0. The "reset" attribute is for documentation only, as set externally.
w0Same as w, but auto-clears to 0 (and thus always reads as 0). At output port, signal will go high for one cycle when bit is written with a 1 (no effect if written to a 0). No "reset" attribute, as must always be 0.
rRead only value. Input ports generated for each field (where applicable), and concatenated on returned read data bus.
rpSimilar to r, but a pulse generated on a read access to the register address to allow peripheral logic to update value. The "reset" attribute is for documentation only, as set externally.
rwpSimilar to wp, but also generates a (separate) pulse on a read access to the register
bitdefDefines the bits used in the read, set, clear registers
  
SubypeDescription
unsignedRegister/field is specified as an unsigned value.
signedRegister/field is specified as a signed value.
<blank>Register/field sign status is not explicitly defined and defaults to unsigned.

 


Copyright © 2024 Global Inkjet Systems. Generated by gen_htm.py —2024-10-30 09:43