Offset in core for bus CSR : 0x0000c000
| shutdown_monitor_0 | This block is the emergency shutdown monitor for HMB-FD-HV | ||||||
|---|---|---|---|---|---|---|---|
| Register Name | Byte Addr Offset | Field | Bits | Type | subtype | Reset | Description |
| CSR_SHUTDOWN_MONITOR_0_IP_ID | 0x0 | 32 | Unique ID for this IP block | ||||
| IP_NUMBER | 7:0 | c | 0x18 | IP identifier number | |||
| MFR_NUMBER | 15:8 | c | 0x00 | Manufacturer number | |||
| RESERVED | 31:16 | rsv | 0 | Reserved bits | |||
| CSR_SHUTDOWN_MONITOR_0_IP_VER | 0x4 | 32 | Bits[7:0] = Minor version number, Bits[15:8] = Major version number, etc. | ||||
| MINOR_NUMBER | 7:0 | c | 0x02 | Minor number | |||
| MAJOR_NUMBER | 15:8 | c | 0x00 | Major number | |||
| RESERVED | 31:16 | rsv | 0 | Reserved bits | |||
| CSR_SHUTDOWN_MONITOR_0_NEW_PWR_MASK | 0x8 | 32 | w | 0 | New mask (masked when low, enabled when high) for power signals from PIO. | ||
| CSR_SHUTDOWN_MONITOR_0_NEW_TRIP_MASK | 0xc | 32 | w | 0 | New mask (masked when low, enabled when high) for trip signals being monitored. | ||
| CSR_SHUTDOWN_MONITOR_0_ACTIVE_PWR_MASK | 0x10 | 32 | r | 0 | New mask (masked when low, enabled when high) for power signals from PIO. | ||
| CSR_SHUTDOWN_MONITOR_0_ACTIVE_TRIP_MASK | 0x14 | 32 | r | 0 | New mask (masked when low, enabled when high) for trip signals being monitored. | ||
| CSR_SHUTDOWN_MONITOR_0_TRIP_MASK_DELAY | 0x18 | 32 | w | 0 | Delay, in system clock cycles (nominally 10ns), from asserting new power mask to asserting trip mask. | ||
| CSR_SHUTDOWN_MONITOR_0_CONTROL | 0x1c | 12 | Control register. | ||||
| GO | 0 | w0 | 0 | Initiate update of new masks when written to 1. | |||
| CLEAR_TRIP | 1 | w0 | 0 | Clear trip state when written to 1. Masks put at reset value---i.e. power mask all set and trip mask all clear. | |||
| ENABLE_WD | 2 | w | 0 | Enable watch dog. | |||
| CLEAR_WD | 3 | w0 | 0 | Clear watch dog. | |||
| WD_PERIOD | 11:4 | w | 10 | Watchdog period in 100ms units. | |||
| CSR_SHUTDOWN_MONITOR_0_STATUS | 0x20 | 2 | Status register. | ||||
| TRIPPED | 0 | r | 0 | Monitor trip status. Tripped when 0. | |||
| WD_ALARM | 1 | r | 0 | Watchdog alarm status. | |||
| CSR_SHUTDOWN_MONITOR_0_BAD_STATUS | 0x24 | 32 | r | 0 | Bad status value. | ||
| CSR_SHUTDOWN_MONITOR_0_BAD_STATUS_SNAPSHOT | 0x28 | 32 | r | 0 | Bad status value latched at trip. | ||
| CSR_SHUTDOWN_MONITOR_0_CHAIN | 0x2c | 32 | Filter chain length. | ||||
| LENGTH | 15:0 | w0 | 0 | Chain length to use in filters as flagged in update field. | |||
| UPDATE | 31:16 | w0 | 0 | Update bits to load length value into filters selected. | |||
| CSR_SHUTDOWN_MONITOR_0_TEST_SHUTDN_SIGNAL | 0x30 | 1 | w | 0 | Set or reset a test shutdown signal (one of the signal monitored by the block, along with the system trips signals). | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY0 | 0x34 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 0. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY1 | 0x38 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 1. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY2 | 0x3c | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 2. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY3 | 0x40 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 3. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY4 | 0x44 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 4. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY5 | 0x48 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 5. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY6 | 0x4c | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 6. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY7 | 0x50 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 7. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY8 | 0x54 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 8. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY9 | 0x58 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 9. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY10 | 0x5c | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 10. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY11 | 0x60 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 11. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY12 | 0x64 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 12. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY13 | 0x68 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 13. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY14 | 0x6c | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 14. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY15 | 0x70 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 15. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY16 | 0x74 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 16. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY17 | 0x78 | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 17. | ||
| CSR_SHUTDOWN_MONITOR_0_SHUTDN_DLY18 | 0x7c | 10 | w | 0 | Shutdown delay, in system clock cycles (nominally 10ns), from shutdown event for signal 18. | ||
Register/field type key:
| Type | Description |
|---|---|
| c | Constant, with value defined by "reset" attribute |
| rsv | Same as constant, except no reset value and always 0. Can be mixed with write types. |
| w | Write register (and read—no write only type). Register defined in register block and reset to "reset" attribute value. Split into fields (if applicable) for signalling and output, where attribute associated with fields, not register. |
| wp | Write with pulse. Register is not declared in block, but write bus split into fields as output port signals, and a pulse generated on write to register address. Register reads back 0. The "reset" attribute is for documentation only, as set externally. |
| w0 | Same as w, but auto-clears to 0 (and thus always reads as 0). At output port, signal will go high for one cycle when bit is written with a 1 (no effect if written to a 0). No "reset" attribute, as must always be 0. |
| r | Read only value. Input ports generated for each field (where applicable), and concatenated on returned read data bus. |
| rp | Similar to r, but a pulse generated on a read access to the register address to allow peripheral logic to update value. The "reset" attribute is for documentation only, as set externally. |
| rwp | Similar to wp, but also generates a (separate) pulse on a read access to the register |
| bitdef | Defines the bits used in the read, set, clear registers |
| Subype | Description |
| unsigned | Register/field is specified as an unsigned value. |
| signed | Register/field is specified as a signed value. |
| <blank> | Register/field sign status is not explicitly defined and defaults to unsigned. |
The shutdown monitor is used in various products to facilitate the powering up and down of power supplies, and the monitoring of critical signals and alerts in order to shutdown the supplies in the case of a failure mode. More details of the shutdown monitor, and its use, can be found at this link .
Copyright © 2024 Global Inkjet Systems. Generated by gen_htm.py —2024-10-30 09:43