gis_logo.png

Datasheet for the GENERIC_DELAY_QUEUE_1 GIS Soft IP Embedded Logic

Register Definitions

Offset in print_unit for bus CSR : 0x00000080

generic_delay_queue_1 This block is the generic delay queue
Register Name Byte Addr Offset Field Bits Type subtype Reset Description
CSR_GENERIC_DELAY_QUEUE_1_IP_ID 0x0 32 Unique ID for this IP block
IP_NUMBER 7:0 c 0x02 IP identifier number
MFR_NUMBER 15:8 c 0xFF Manufacturer number
RESERVED 31:16 rsv 0 Reserved bits
CSR_GENERIC_DELAY_QUEUE_1_IP_VER 0x4 32 Bits[7:0] = Minor version number, Bits[15:8] = Major version number, etc.
MINOR_NUMBER 7:0 c 0x01 Minor number
MAJOR_NUMBER 15:8 c 0x00 Major number
RESERVED 31:16 rsv 0 Reserved bits
CSR_GENERIC_DELAY_QUEUE_1_CONFIG 0x8 30 Configuration status
LOG2_LENGTH_DEPTH 5:0 r 0x00 LOG2 of LENGTH_DEPTH generic
LOG2_DELAY_DEPTH 11:6 r 0x00 LOG2 of DELAY_DEPTH generic
LOG2_DATA_DEPTH 17:12 r 0x00 LOG2 of DATA_DEPTH generic
DELAY_WIDTH 23:18 r 0x00 DELAY_WIDTH generic
DATA_WIDTH 29:24 r 0x00 DATA_WIDTH generic
CSR_GENERIC_DELAY_QUEUE_1_CTRL_MODE 0xc 2 wp 0 Control mode of block. 0=>disabled, 1=>bypass, 2=>cpu, 3=>normal or streaming (if PKT_MODE)
CSR_GENERIC_DELAY_QUEUE_1_DATA 0x10 32 wp 0 Sets the CPU ingress data and packet delay (when in CPU mode). As the widths of these are dependent on generics, and occupy consecutive bits, the field widths are undefined, except that the ingress data is the first DATA_WIDTH bits and the packet delay is the next DELAY_WIDTH bits, as defined in the CONFIG register

Register/field type key:

TypeDescription
cConstant, with value defined by "reset" attribute
rsvSame as constant, except no reset value and always 0. Can be mixed with write types.
wWrite register (and read—no write only type). Register defined in register block and reset to "reset" attribute value. Split into fields (if applicable) for signalling and output, where attribute associated with fields, not register.
wpWrite with pulse. Register is not declared in block, but write bus split into fields as output port signals, and a pulse generated on write to register address. Register reads back 0. The "reset" attribute is for documentation only, as set externally.
w0Same as w, but auto-clears to 0 (and thus always reads as 0). At output port, signal will go high for one cycle when bit is written with a 1 (no effect if written to a 0). No "reset" attribute, as must always be 0.
rRead only value. Input ports generated for each field (where applicable), and concatenated on returned read data bus.
rpSimilar to r, but a pulse generated on a read access to the register address to allow peripheral logic to update value. The "reset" attribute is for documentation only, as set externally.
rwpSimilar to wp, but also generates a (separate) pulse on a read access to the register
bitdefDefines the bits used in the read, set, clear registers
  
SubypeDescription
unsignedRegister/field is specified as an unsigned value.
signedRegister/field is specified as a signed value.
<blank>Register/field sign status is not explicitly defined and defaults to unsigned.

Usage Notes

This is the generic delay queue component, used in various projects. Details of this block can be found at this link

 


Copyright © 2024 Global Inkjet Systems. Generated by gen_htm.py —2024-10-30 09:43