Offset in print_unit for bus CSR : 0x00000080
| generic_delay_queue_1 | This block is the generic delay queue | ||||||
|---|---|---|---|---|---|---|---|
| Register Name | Byte Addr Offset | Field | Bits | Type | subtype | Reset | Description |
| CSR_GENERIC_DELAY_QUEUE_1_IP_ID | 0x0 | 32 | Unique ID for this IP block | ||||
| IP_NUMBER | 7:0 | c | 0x02 | IP identifier number | |||
| MFR_NUMBER | 15:8 | c | 0xFF | Manufacturer number | |||
| RESERVED | 31:16 | rsv | 0 | Reserved bits | |||
| CSR_GENERIC_DELAY_QUEUE_1_IP_VER | 0x4 | 32 | Bits[7:0] = Minor version number, Bits[15:8] = Major version number, etc. | ||||
| MINOR_NUMBER | 7:0 | c | 0x01 | Minor number | |||
| MAJOR_NUMBER | 15:8 | c | 0x00 | Major number | |||
| RESERVED | 31:16 | rsv | 0 | Reserved bits | |||
| CSR_GENERIC_DELAY_QUEUE_1_CONFIG | 0x8 | 30 | Configuration status | ||||
| LOG2_LENGTH_DEPTH | 5:0 | r | 0x00 | LOG2 of LENGTH_DEPTH generic | |||
| LOG2_DELAY_DEPTH | 11:6 | r | 0x00 | LOG2 of DELAY_DEPTH generic | |||
| LOG2_DATA_DEPTH | 17:12 | r | 0x00 | LOG2 of DATA_DEPTH generic | |||
| DELAY_WIDTH | 23:18 | r | 0x00 | DELAY_WIDTH generic | |||
| DATA_WIDTH | 29:24 | r | 0x00 | DATA_WIDTH generic | |||
| CSR_GENERIC_DELAY_QUEUE_1_CTRL_MODE | 0xc | 2 | wp | 0 | Control mode of block. 0=>disabled, 1=>bypass, 2=>cpu, 3=>normal or streaming (if PKT_MODE) | ||
| CSR_GENERIC_DELAY_QUEUE_1_DATA | 0x10 | 32 | wp | 0 | Sets the CPU ingress data and packet delay (when in CPU mode). As the widths of these are dependent on generics, and occupy consecutive bits, the field widths are undefined, except that the ingress data is the first DATA_WIDTH bits and the packet delay is the next DELAY_WIDTH bits, as defined in the CONFIG register | ||
Register/field type key:
| Type | Description |
|---|---|
| c | Constant, with value defined by "reset" attribute |
| rsv | Same as constant, except no reset value and always 0. Can be mixed with write types. |
| w | Write register (and read—no write only type). Register defined in register block and reset to "reset" attribute value. Split into fields (if applicable) for signalling and output, where attribute associated with fields, not register. |
| wp | Write with pulse. Register is not declared in block, but write bus split into fields as output port signals, and a pulse generated on write to register address. Register reads back 0. The "reset" attribute is for documentation only, as set externally. |
| w0 | Same as w, but auto-clears to 0 (and thus always reads as 0). At output port, signal will go high for one cycle when bit is written with a 1 (no effect if written to a 0). No "reset" attribute, as must always be 0. |
| r | Read only value. Input ports generated for each field (where applicable), and concatenated on returned read data bus. |
| rp | Similar to r, but a pulse generated on a read access to the register address to allow peripheral logic to update value. The "reset" attribute is for documentation only, as set externally. |
| rwp | Similar to wp, but also generates a (separate) pulse on a read access to the register |
| bitdef | Defines the bits used in the read, set, clear registers |
| Subype | Description |
| unsigned | Register/field is specified as an unsigned value. |
| signed | Register/field is specified as a signed value. |
| <blank> | Register/field sign status is not explicitly defined and defaults to unsigned. |
This is the generic delay queue component, used in various projects. Details of this block can be found at this link
Copyright © 2024 Global Inkjet Systems. Generated by gen_htm.py —2024-10-30 09:43