Offset in enc_pd_emul_2 for bus CSR : 0x00000080
Offset in pulse_generator_5 for bus CSR : 0x00000080
| generic_sequencer_18 | Generic Sequencer core | ||||||
|---|---|---|---|---|---|---|---|
| Register Name | Byte Addr Offset | Field | Bits | Type | subtype | Reset | Description |
| CSR_GENERIC_SEQUENCER_18_IP_ID | 0x0 | 32 | Unique ID for this IP block | ||||
| IP_NUMBER | 7:0 | c | 0x01 | IP identifier number | |||
| MFR_NUMBER | 15:8 | c | 0xFF | Manufacturer number | |||
| RESERVED | 31:16 | rsv | 0 | Reserved bits | |||
| CSR_GENERIC_SEQUENCER_18_IP_VER | 0x4 | 32 | Bits[7:0] = Minor version number, Bits[15:8] = Major version number, etc. | ||||
| MINOR_NUMBER | 7:0 | c | 0x01 | Minor number | |||
| MAJOR_NUMBER | 15:8 | c | 0x12 | Major number | |||
| RESERVED | 31:16 | rsv | 0 | Reserved bits | |||
| CSR_GENERIC_SEQUENCER_18_CONFIG | 0x8 | 31 | Configuration values for sequencer | ||||
| SEQ_DEPTH | 3:0 | r | 0 | LOG2 of SEQ_DEPTH generic | |||
| POS_WIDTH | 9:4 | r | 0 | POS_WIDTH generic value | |||
| BUS_WIDTH | 15:10 | r | 0 | BUS_WIDTH generic value | |||
| VECTOR_WIDTH | 20:16 | r | 0 | VECTOR_WIDTH generic value | |||
| TRIGGER_WIDTH | 25:21 | r | 0 | TRIGGER_WIDTH generic value | |||
| RAMP_WIDTH | 30:26 | r | 0 | RAMP_WIDTH generic value | |||
| CSR_GENERIC_SEQUENCER_18_CTRL_W | 0xc | 11 | Control register write fields | ||||
| SEQ_ENABLE | 0 | w | 0 | Master enable for the sequencer | |||
| RESERVED_0 | 2:1 | rsv | 0 | Reserved bits | |||
| DEBUG_MODE | 3 | w | 0 | Enter debug mode (only has effect if not busy) | |||
| RST_VECTOR_OUT | 4 | w | 0 | Reset vector_out when start_req is asserted | |||
| RESERVED_1 | 7:5 | rsv | 0 | Reserved bits | |||
| CLR_SEQ_QUEUE | 8 | w0 | 0 | Clear the sequencer queue | |||
| CLR_SEQ_QUEUE_EXE | 9 | w0 | 0 | Clear the executed sequences counter | |||
| RESERVED_2 | 10 | rsv | 0 | Reserved bits | |||
| CSR_GENERIC_SEQUENCER_18_CTRL_R | 0x10 | 11 | Control register read fields | ||||
| RESERVED_0 | 1:0 | rsv | 0 | Reserved bits | |||
| BUSY | 2 | r | 0 | Busy status (writing has no effect---in this register for backwards compatibility) | |||
| RESERVED_1 | 9:3 | rsv | 0 | Reserved bits | |||
| SEQ_QUEUE_EMPTY | 10 | r | 0 | asserted when End-and-Queue is executed with queue_left = 0. Cleared upon reading | |||
| CSR_GENERIC_SEQUENCER_18_PC | 0x14 | 32 | RAM addresses of sequencer | ||||
| RAM_RD_ADDR | 11:0 | r | 0 | Current RAM read address | |||
| RESERVED_0 | 15:12 | rsv | 0 | Reserved bits | |||
| RETURN_ADDR | 27:16 | r | 0 | Current return address | |||
| RESERVED_1 | 31:28 | rsv | 0 | Reserved bits | |||
| CSR_GENERIC_SEQUENCER_18_TRIGGER | 0x18 | 16 | r | 0 | Trigger input vector value | ||
| CSR_GENERIC_SEQUENCER_18_VECTOR | 0x1c | 24 | wp | 0 | Vector output override from CPU | ||
| CSR_GENERIC_SEQUENCER_18_R1 | 0x20 | 12 | wp | 0 | R1 register access. Writes only effective when idle. | ||
| CSR_GENERIC_SEQUENCER_18_STEP | 0x24 | 1 | w0 | 0 | Step request from CPU | ||
| CSR_GENERIC_SEQUENCER_18_AUX_CONFIG | 0x28 | 6 | Aux Configuration values for sequencer | ||||
| ADD_VEC_PIPE | 0 | r | 0 | Add 1 level of pipeline on vector_out | |||
| VECT_RAMP_EN | 1 | r | 0 | Enable support for VEC_RAMP_UP/DN instructions | |||
| BUS_BURST_EN | 2 | r | 0 | Enable support for BUS_BURST instructions | |||
| POS_BUS_EN | 3 | r | 0 | Enable support for POS input bus | |||
| ALU_EN | 4 | r | 0 | Enable support for ALU instruction | |||
| QUEUE_EN | 5 | r | 0 | Enable support for End-and-Queue instruction | |||
| CSR_GENERIC_SEQUENCER_18_POS_STORE | 0x2c | 32 | r | signed | 0 | value of pos_store | |
| CSR_GENERIC_SEQUENCER_18_SEQ_QUEUE_W | 0x30 | 8 | wp | 0 | Sequence Execution Queue write | ||
| CSR_GENERIC_SEQUENCER_18_SEQ_QUEUE_R | 0x34 | 32 | Sequence Execution Queue read bits | ||||
| RESERVED_0 | 7:0 | rsv | 0 | Reserved bits | |||
| QUEUE_LEFT | 15:8 | r | 0 | Number of sequences currently in the queue | |||
| QUEUE_EXEC | 31:16 | r | 0 | Number of sequences executed | |||
Register/field type key:
| Type | Description |
|---|---|
| c | Constant, with value defined by "reset" attribute |
| rsv | Same as constant, except no reset value and always 0. Can be mixed with write types. |
| w | Write register (and read—no write only type). Register defined in register block and reset to "reset" attribute value. Split into fields (if applicable) for signalling and output, where attribute associated with fields, not register. |
| wp | Write with pulse. Register is not declared in block, but write bus split into fields as output port signals, and a pulse generated on write to register address. Register reads back 0. The "reset" attribute is for documentation only, as set externally. |
| w0 | Same as w, but auto-clears to 0 (and thus always reads as 0). At output port, signal will go high for one cycle when bit is written with a 1 (no effect if written to a 0). No "reset" attribute, as must always be 0. |
| r | Read only value. Input ports generated for each field (where applicable), and concatenated on returned read data bus. |
| rp | Similar to r, but a pulse generated on a read access to the register address to allow peripheral logic to update value. The "reset" attribute is for documentation only, as set externally. |
| rwp | Similar to wp, but also generates a (separate) pulse on a read access to the register |
| bitdef | Defines the bits used in the read, set, clear registers |
| Subype | Description |
| unsigned | Register/field is specified as an unsigned value. |
| signed | Register/field is specified as a signed value. |
| <blank> | Register/field sign status is not explicitly defined and defaults to unsigned. |
This is the generic sequencer processing element core used in various products for a variety of purposes, such as pulse generation control, waveform generation for analogue heads and print data control. More details of this component can be found at this link
Copyright © 2024 Global Inkjet Systems. Generated by gen_htm.py —2024-10-30 09:43