31 KiB
[INTERACTIVE COMMANDS]
calibrate
Usage: calibrate <operation> [options]
Perform the specified transceiver calibration operation.
Available operations:
-
LMS internal DC offset auto-calibrations
calibrate lms [show]calibrate lms tuning [value]calibrate lms txlpf [<I filter> <Q filter>]calibrate lms rxlpf [<I filter> <Q filter>]calibrate lms rxvga2 [<DC ref> <I1> <Q1> <I2> <Q2>]
Perform the specified auto-calibration, or all of them if none are provided. When values are provided, these are used instead of the results of the auto-calibration procedure. Use
lms showto read and print the current LMS calibration values.For
rxvga2,I1andQ1are the Stage 1 I and Q components respectively, andI2andQ2are the Stage 2 I and Q components. -
RX and TX I/Q DC offset correction parameter calibration
calibrate dc <rx|tx> [<I> <Q>]calibrate dc <rxtx>
Calibrate the DC offset correction parameters for the current frequency and gain settings. If a I/Q values are provided, they are applied directly.
cal rxtxis shorthand forcal rxfollowed bycal tx. -
RX and TX I/Q balance correction parameter calibration
calibrate iq <rx|tx> <gain|phase> <value>
Set the specified IQ gain or phase balance parameters.
-
Generate RX or TX I/Q DC correction parameter tables
calibrate table dc <rx|tx> [<f_min> <f_max> [f_inc]]
Generate and write an I/Q correction parameter table to the current working directory, in a file named
<serial>_dc_<rx|tx>.tbl.f_minandf_maxare min and max frequencies to include in the table.f_incis the frequency increment.By default, tables are generated over the entire frequency range, in 10 MHz steps.
-
Generate RX or TX I/Q DC correction parameter tables for AGC Look Up Table
calibrate table agc <rx|tx> [<f_min> <f_max> [f_inc]]
Similar usage as
calibrate table dcexcept the call will set gains to the AGC's base gain value before runningcalibrate table dc.
clear
Usage: clear
Clears the screen.
echo
Usage: echo [arg 1] [arg 2] ... [arg n]
Echo each argument on a new line.
erase
Usage: erase <offset> <count>
Erase specified erase blocks SPI flash.
<offset>- Erase block offset<count>- Number of erase blocks to erase
flash_backup
Usage: flash_backup <file> (<type> | <address> <length>)
Back up flash data to the specified file. This command takes either two or four arguments. The two-argument invocation is generally recommended for non-development use.
Parameters:
-
<type>- Type of backup.This selects the appropriate address and length values based upon the selected type.
Valid options are:
Option Description
calCalibration datafwFirmwarefpga40Metadata and bitstream for 40 kLE FPGAfpga115Metadata and bitstream for 115 kLE FPGAfpgaA4Metadata and bitstream for 49 kLE (A4) FPGAfpgaA5Metadata and bitstream for 77 kLE (A5) FPGAfpgaA9Metadata and bitstream for 301 kLE (A9) FPGA -
<address>- Address of data to back up. Must be erase block-aligned. -
<len>- Length of region to back up. Must be erase block-aligned.
Note: When an address and length are provided, the image type will default
to raw.
Examples:
-
flash_backup cal.bin calBacks up the calibration data region.
-
flash_backup cal_raw.bin 0x30000 0x10000Backs up the calibration region as a raw data image.
flash_image
Usage: flash_image <image> [output options]
Print a flash image's metadata or create a new flash image. When provided with the name of a flash image file as the only argument, this command will print the metadata contents of the image.
The following options may be used to create a new flash image.
-
data=<file>File to containing data to store in the image.
-
address=<addr>Flash address. The default depends upon
typeparameter. -
type=<type>Type of flash image. Defaults to
raw.Valid options are:
Option Description
calCalibration datafwFirmwarefpga40Metadata and bitstream for 40 kLE FPGAfpga115Metadata and bitstream for 115 kLE FPGAfpgaA4Metadata and bitstream for 49 kLE (A4) FPGAfpgaA5Metadata and bitstream for 77 kLE (A5) FPGAfpgaA9Metadata and bitstream for 301 kLE (A9) FPGArawRaw data. The address and length parameters must be provided if this type is selected. -
serial=<serial>Serial # to store in image. Defaults to zeros.
flash_init_cal
Usage: flash_init_cal <fpga_size> <vctcxo_trim> [<output_file>]
Create and write a new calibration data region to the currently opened
device, or to a file. Be sure to back up calibration data prior to running
this command. (See the flash_backup command.)
-
<fpga_size>Either 40 or 115, depending on the device model.
-
<vctcxo_trim>VCTCXO/DAC trim value (
0x0-0xffff) -
<output_file>File to write calibration data to. When this argument is provided, no data will be written to the device's flash.
flash_restore
Usage: flash_restore <file> [<address> <length>]
Restore flash data from a file, optionally overriding values in the image metadata.
-
<address>Defaults to the address specified in the provided flash image file.
-
<length>Defaults to length of the data in the provided image file.
fw_log
Usage: fw_log [filename]
Read the contents of the device's firmware log and write it to the specified file. If no filename is specified, the log content is written to stdout.
generate
Usage: generate <filename> [parameters] <signal_type>
Configuration parameters take the form param=value, and may be specified in a single or multiple rx config invocations. Below is a list of available parameters.
---------------------------------------------------------------------------
Parameter Description
----------------- ---------------------------------------------------------
n Number of samples to generate. 0 = unlimited.
mag Magnitude of signal [-mag, mag]. Default is 2047
format Output file format. One of the following:
csv: CSV of SC16 Q11 or SC8 Q7 samples (default)
bin: Raw SC16 Q11 or SC8 Q7 DAC samples
Note: Sample format will depend on the
bitmode state
Generates signal for use with tx command. Signal types include:
-
cw
Generate a complex tone with a period relative to system sampling rate
period indicates the number of samples between 2*M_PI. For example, cw of 4 would generate a complex tone at +4/F_s. With a sampling rate of 20MSPS, the complex tone would be generated at +5MHz. A negative period indicates negative frequency.
-
prn
Generates pseudorandom noise \
Examples:
-
To generate a CSV for a complex tone at -F_s/4 with a full scale swing of -500 to 500:
generate output.csv format=csv mag=500 cw 4
-
To generate 10,000,000 samples of PRN:
generate output.csv format=csv n=10e6 prn
help
Usage: help [<command>]
Provides extended help, like this, on any command.
info
Usage: info
Prints the following information about an opened device:
- Serial number
- VCTCXO DAC calibration value
- FPGA size
- Whether or not the FPGA is loaded
- USB bus, address, and speed
- Backend (Denotes which device interface code is being used.)
- Instance number
help
Usage: help [<command>]
Provides extended help, like this, on any command.
info
Usage: info
Prints the following information about an opened device:
- Serial number
- VCTCXO DAC calibration value
- FPGA size
- Whether or not the FPGA is loaded
- USB bus, address, and speed
- Backend (Denotes which device interface code is being used.)
- Instance number
jump_to_boot
Usage: jump_to_boot
Clear out a FW signature word in flash and jump to FX3 bootloader.
The device will continue to boot into the FX3 bootloader across power cycles until new firmware is written to the device.
load
Usage: load <fpga|fx3> <filename>
Load an FPGA bitstream or program the FX3's SPI flash.
xb
Usage: xb <board_model> <subcommand> [parameters]
Enable or configure an expansion board.
Valid values for board_model:
-
100XB-100 GPIO expansion board
-
200XB-200 LF/MF/HF/VHF transverter expansion board
-
300XB-300 amplifier board
Common subcommands:
-
enableEnable the XB-100, XB-200, or XB-300 expansion board.
XB-200 subcommands:
-
filter [rx|tx] [50|144|222|custom|auto_1db|auto_3db]Selects the specified RX or TX filter on the XB-200 board. Below are descriptions of each of the filter options.
-
50
Select the 50-54 MHz (6 meter band) filter. -
144
Select the 144-148 MHz (2 meter band) filter. -
222
Select the 222-225 MHz (1.25 meter band) filter. Realistically, this filter option is actually slightly wider, covering 206 MHz - 235 MHz. -
custom
Selects the custom filter path. The user should connect a filter along the corresponding FILT and FILT-ANT connections when using this option. Alternatively one may jumper the FILT and FILT-ANT connections to achieve "no filter" for reception. (However, this is _highly_ discouraged for transmissions.) -
auto_1db
Automatically selects one of the above choices based upon frequency and the filters' 1dB points. The custom path is used for cases that are not associated with the on-board filters. -
auto_3db
Automatically selects one of the above choices based upon frequency and the filters' 3dB points. The custom path is used for cases that are not associated with the on-board filters.
-
XB-300 subcommands:
-
<pa|lna|aux> [on|off]Enable or disable the power amplifier (PA), low-noise amplifier (lna) or auxillary LNA (aux). The current state if the specified device is printed if [on|off] is not specified.
Note: The auxillary path on the XB-300 is not populated with components by default; the
auxcontrol will have no effect upon the RX signal. This option is available for users to modify their board with custom hardware. -
<pwr>Read the current Power Detect (PDET) voltage and compute the output power.
-
trx <rx|tx>The default XB-300 hardware configuration includes separate RX and TX paths. However, users wishing to use only a single antenna for TRX can do so via a modification to resistor population options on the XB-300 and use this command to switch between RX an TX operation. (See R8, R10, and R23 on the schematic.)
Examples:
-
xb 200 enableEnables and configures the XB-200 transverter expansion board.
-
xb 200 filter rx 144Selects the 144-148 MHz receive filter on the XB-200 transverter expansion board.
-
xb 300 enableEnables and configures the use of GPIOs to interact with the XB-300. The PA and LNA will disabled by default.
-
xb 300 lna onEnables the RX LNA on the XB-300. LED D1 (green) is illuminated when the LNA is enabled, and off when it is disabled.
-
xb 300 pa offDisables the TX PA on the XB-300. LED D2 (blue) is illuminated when the PA is enabled, and off when it is disabled.
mimo
Usage: mimo [master | slave]
Modify device MIMO operation.
IMPORTANT: This command is deprecated and has been superseded by
"print/set smb_mode". For usage text, run: "set smb_mode"
open
Usage: open [device identifiers]
Open the specified device for use with successive commands. Any previously opened device will be closed.
The general form of the device identifier string is:
<backend>:[device=<bus>:<addr>] [instance=<n>] [serial=<serial>]
See the bladerf_open() documentation in libbladeRF for the complete
device specifier format.
peek
Usage: peek <rfic|pll|dac|lms|si> <address> [num_addresses]
The peek command can read any of the devices hanging off the FPGA. This includes the:
- bladeRF 1: LMS6002D transceiver, VCTCXO trim DAC, Si5338 clock generator
- bladeRF 2: AD9361 transceiver, VCTCXO trim DAC, ADF4002 frequency synthesizer
If num_addresses is supplied, the address is incremented by 1 and
another peek is performed for that many addresses.
Valid Address Ranges:
Device Address Range
rfic 0 to 0x3F7 (1015)
pll 0 to 3
dac 0 to 255
lms 0 to 127
si 0 to 255
Example:
peek si ...
poke
Usage: poke <rfic|pll|dac|lms|si> <address> <data>
The poke command can write any of the devices hanging off the FPGA. This includes the:
- bladeRF 1: LMS6002D transceiver, VCTCXO trim DAC, Si5338 clock generator
- bladeRF 2: AD9361 transceiver, VCTCXO trim DAC, ADF4002 frequency synthesizer
Valid Address Ranges:
Device Address Range
rfic 0 to 0x3F7 (1015)
pll 0 to 3
dac 0 to 255
lms 0 to 127
si 0 to 255
Example:
poke lms ...
Usage: print [parameter]
The print command takes a parameter to print. Available parameters are listed
below. If no parameter is specified, all parameters are printed.
Common parameters:
Parameter Description
bandwidth Bandwidth settings
frequency Frequency settings
agc Automatic gain control
loopback Loopback settings
rx_mux FPGA RX FIFO input mux setting
gain Gain settings
samplerate Samplerate settings
trimdac VCTCXO Trim DAC settings
tuning_mode Tuning mode settings
bitmode Sample bit width
hardware Low-level hardware status
BladeRF1-only parameters:
Parameter Description
gpio FX3 <-> FPGA GPIO state
lnagain RX LNA gain, in dB (deprecated)
rxvga1 RXVGA1 gain, in dB (deprecated)
rxvga2 RXVGA2 gain, in dB (deprecated)
txvga1 TXVGA1 gain, in dB (deprecated)
txvga2 TXVGA2 gain, in dB (deprecated)
sampling External or internal sampling mode
smb_mode SMB clock port mode of operation
vctcxo_tamer Current VCTCXO tamer mode
xb_gpio Expansion board GPIO values
xb_gpio_dir Expansion board GPIO direction (1=output, 0=input)
BladeRF2-only parameters:
Parameter Description
clock_sel System clock selection
clock_out Clock output selection
rssi Received signal strength indication
clock_ref ADF4002 chip status
refin_freq ADF4002 reference clock frequency
biastee Current bias-tee status
filter RFIC FIR filter selection
probe
Usage: probe [strict]
Search for attached bladeRF device and print a list of results.
Without specifying strict, the lack of any available devices is not considered
an error.
When provided the optional strict argument, this command will treat the
situation where no devices are found as an error, causing scripts or
lists of commands provided via the -e command line argument to terminate
immediately.
quit
Usage: quit
Exit the CLI.
recover
Usage: recover [<bus> <address> <firmware file>]
Load firmware onto a device running in bootloader mode, or list all devices currently in bootloader mode.
With no arguments, this command lists the USB bus and address for FX3-based devices running in bootloader mode.
When provided a bus, address, and path to a firmware file, the specified device will be loaded with and begin executing the provided firmware.
In most cases, after successfully loading firmware into the device's RAM,
users should open the device with the "open" command, and write the
firmware to flash via "load fx3 <firmware file>"
run
Usage: run <script>
Run the provided script.
rx
Usage: rx <start | stop | wait | config [param=val [param=val [...]]>
Receive IQ samples and write them to the specified file. Reception is controlled and configured by one of the following:
Command Description
start Start receiving samples
stop Stop receiving samples
wait Wait for sample transmission to complete, or until a
specified amount of time elapses
config Configure sample reception. If no parameters are
provided, the current parameters are printed.
Running rx without any additional commands is valid shorthand for
rx config.
The wait command takes an optional timeout parameter. This parameter
defaults to units of milliseconds (ms). The timeout unit may be specified
using the ms or s suffixes. If this parameter is not provided, the
command will wait until the reception completes or Ctrl-C is pressed.
Configuration parameters take the form param=value, and may be specified
in a single or multiple rx config invocations. Below is a list of
available parameters.
Parameter Description
n Number of samples to receive. 0 = inf.
file Filename to write received samples to
format Output file format. One of the following:
`csv`: CSV of SC16 Q11 or SC8 Q7 samples
`bin`: Raw SC16 Q11 or SC8 Q7 DAC samples
Note: Sample format will depend on the
`bitmode` state
samples Number of samples per buffer to use in the
asynchronous stream. Must be divisible by 1024 and
>= 1024.
buffers Number of sample buffers to use in the asynchronous
stream. The min value is 4.
xfers Number of simultaneous transfers to allow the
asynchronous stream to use. This should be less than
the buffers parameter.
timeout Data stream timeout. With no suffix, the default
unit is ms. The default value is 1000 ms (1 s).
Valid suffixes are ms and s.
channel Comma-delimited list of physical RF channels to use
Example:
-
rx config file=/tmp/data.bin format=bin n=10KReceive (10240 = 10 * 1024) samples, writing them to
/tmp/data.binin the binary DAC format. -
rx config file=mimo.csv format=csv n=32768 channel=1,2Receive 32768 samples from RX1 and RX2, outputting them to a file named
mimo.csv, with four columns (RX1 I, RX1 Q, RX2 I, RX2 Q).
Notes:
- The
n,samples,buffers, andxfersparameters support the suffixesK,M, andG, which are multiples of 1024. - An
rx stopfollowed by anrx startwill result in the samples file being truncated. If this is not desired, be sure to runrx configto set another file before restarting the rx stream. - For higher sample rates, it is advised that the
binary output format be used, and the output file be written to RAM (e.g./tmp,/dev/shm), if space allows. For larger captures at higher sample rates, consider using an SSD instead of a HDD. - The CSV format produces two columns per channel, with the first two columns
corresponding to the I,Q pair for the first channel configured with the
channelparameter; the next two columns corresponding to the I,Q of the second channel, and so on.
trigger
Usage: trigger [<trigger> <tx | rx> [<off slave master fire>]]
If used without parameters, this command prints the state of all triggers. When and <tx | rx> and supplied, the specified trigger is printed.
Below are the available options for :
Trigger Description
J71-4 Trigger signal is on mini_exp1 (bladeRF x40/x115, J71, pin 4).
J51-1 Trigger signal is on mini_exp1 (bladeRF xA4/xA5/xA9, J51, pin 1).
Miniexp-1 Trigger signal is on mini_exp1, hardware-independent
Note that all three of the above options map to the same logical port on
all devices (mini_exp[1]). Multiple options are provided for reverse
compatibility and clarity.
The trigger is controlled and configured by providing the last argument, which may be one of the following:
Command Description
off Clears fire request and disables trigger functionality.
slave Configures trigger as slave, clears fire request, and
arms the device.
master Configures trigger as master, clears fire request, and
arms the device.
fire Sets fire request. Only applicable to the master.
A trigger chain consists of a single or multiple bladeRF units and may contain TX and RX modules. If multiple bladeRF units are used they need to be connected via the signal specified by and a common ground.
The following sequence of commands should be used to ensure proper synchronization. It is assumed that all triggers are off initially.
-
Configure designated trigger master
IMPORTANT
Never configure two devices as trigger masters on a single chain. Contention on the same signal could damage the devices.
-
Configure all other devices as trigger slaves
-
Configure and start transmit or receive streams.
The operation will stall until the triggers fire. As such, sufficiently large timeouts should be used to allow the trigger signal to be emitted by the master and received by the slaves prior to libbladeRF returning BLADERF_ERR_TIMEOUT.
-
Set fire-request on master trigger
All devices will synchronously start transmitting or receiving data.
-
Finish the transmit and receive tasks as usual
-
Re-configure the master and slaves to clear fire requests and re-arm.
Steps 1 through 5 may be repeated as neccessary.
-
Disable triggering on all slaves
-
Disable triggering on master
Notes:
- Synchronizing transmitters and receivers on a single chain will cause an offset of 11 samples between TX and RX; these samples should be discarded. This is caused by different processing pipeline lengths of TX and RX. This value might change if the FPGA code is updated in the future.
tx
Usage: tx <start | stop | wait | config [parameters]>
Read IQ samples from the specified file and transmit them. Transmission is controlled and configured by one of the following:
Command Description
start Start transmitting samples
stop Stop transmitting samples
wait Wait for sample transmission to complete, or until a
specified amount of time elapses
config Configure sample transmission. If no parameters are
provided, the current parameters are printed.
Running tx without any additional commands is valid shorthand for
tx config.
The wait command takes an optional timeout parameter. This parameter
defaults to units of milliseconds (ms). The timeout unit may be specified
using the ms or s suffixes. If this parameter is not provided, the
command will wait until the transmission completes or Ctrl-C is pressed.
Configuration parameters take the form param=value, and may be specified
in a single or multiple tx config invocations. Below is a list of
available parameters.
Parameter Description
file Filename to read samples from
format Input file format. One of the following:
`csv`: CSV of SC16 Q11 or SC8 Q7 samples
`bin`: Raw SC16 Q11 or SC8 Q7 DAC samples
Note: Sample format will depend on the `bitmode` state
repeat The number of times the file contents should be
transmitted. 0 implies repeat until stopped.
delay The number of microseconds to delay between
retransmitting file contents. 0 implies no delay.
samples Number of samples per buffer to use in the
asynchronous stream. Must be divisible by 1024 and
>= 1024.
buffers Number of sample buffers to use in the asynchronous
stream. The min value is 4.
xfers Number of simultaneous transfers to allow the
asynchronous stream to use. This should be < the
buffers parameter.
timeout Data stream timeout. With no suffix, the default
unit is ms. The default value is 1000 ms (1 s).
Valid suffixes are 'ms' and 's'.
channel Comma-delimited list of physical RF channels to use
Example:
-
tx config file=data.bin format=bin repeat=2 delay=250000Transmitting the contents of
data.bintwo times, with a ~250ms delay between transmissions. -
tx config file=mimo.csv format=csv repeat=0 channel=1,2Transmitting the contents of
mimo.csvrepeatedly, with the first channel in the file mapped to channel TX1 and the second channel mapped to TX2.
Notes:
- The
n,samples,buffers, andxfersparameters support the suffixesK,M, andG, which are multiples of 1024. - For higher sample rates, it is advised that the input file be
stored in RAM (e.g.
/tmp,/dev/shm) or on an SSD, rather than a HDD. - The CSV format expects two columns per channel, with the first two columns
corresponding to the I,Q pair for the first channel configured with the
channelparameter; the next two columns corresponding to the I,Q of the second channel, and so on. For example, in the mimo.csv example above,-128,128,-256,256would transmit (-128,128) on TX1 and (-256,256) on TX2. - When providing CSV data, this command will first convert it to a binary format, stored in a file in the current working directory. During this process, out-of-range values will be clamped.
- When using a binary format, the user is responsible for ensuring that the provided data values are within the allowed range. This prerequisite alleviates the need for this program to perform range checks in time-sensitive callbacks.
set
Usage: set <parameter> <arguments>
The set command takes a parameter and an arbitrary number of arguments for
that particular parameter. In general, set <parameter> will display
more help for that parameter.
Common parameters:
Parameter Description
bandwidth Bandwidth settings
frequency Frequency settings
agc Automatic gain control
loopback Loopback settings
rx_mux FPGA RX FIFO input mux mode
gain Gain settings
samplerate Samplerate settings
trimdac VCTCXO Trim DAC settings
tuning_mode Tuning mode settings
bitmode Sample bit width
BladeRF1-only parameters:
Parameter Description
gpio FX3 <-> FPGA GPIO state
lnagain RX LNA gain, in dB. Values: 0, 3, 6
(deprecated)
rxvga1 RXVGA1 gain, in dB. Range: [5, 30]
(deprecated)
rxvga2 RXVGA2 gain, in dB. Range: [0, 30]
(deprecated)
txvga1 TXVGA1 gain, in dB. Range: [-35, -4]
(deprecated)
txvga2 TXVGA2 gain, in dB. Range: [0, 25]
(deprecated)
sampling External or internal sampling mode
smb_mode SMB clock port mode of operation
vctcxo_tamer VCTCXO tamer mode. Options: Disabled, 1PPS, 10MHz
xb_gpio Expansion board GPIO values
xb_gpio_dir Expansion board GPIO direction (1=output, 0=input)
BladeRF2-only parameters:
Parameter Description
clock_sel System clock selection
clock_out Clock output selection
rssi Received signal strength indication
clock_ref Enables (1) or disables (0) the ADF4002 chip
refin_freq ADF4002 reference clock frequency
biastee Enables or disables the bias tee on a given channel
filter RFIC FIR filter selection
version
Usage: version
Prints version information for host software and the current device.