- Move fx3_gpif[14] to pin P7
- Move fx3_ctl[9] to pin V6
This mod allows fx3_ctl[9] to operate as DCLK during FPGA configuration,
and also as fx3_ctl[9] afterward. Pin moves to keep the stub as short as
possible. PIN_V6 is as close as we can get to DCLK (PIN_V3).
- Move i2c1_* to Bank 5A (2.5 V)
- Add adf_muxout to Bank 5B (3.3 V)
- Add adf_ce to Bank 5B (3.3 V)
- Rename exp_present to exp_present_n (active low)
- Move c5_clock_2 to Bank 7A
- Delete exp_spi_*
- Add exp_gpio[27:16]
- Deleted i2c2_sda, i2c2_scl (one CYA I2C bus is enough)
- Bank 5A to 3.3 V (will require FX3 VIO4=3.3 V and 3.3 V flash)
- Moved i2c1_sda/scl to Bank 5A
- Moved adi_*sp4t* (RF switches) to Bank 5A
This change lets us move all the signals that absolutely need to be
3.3 V to a bank that will not have a variable voltage. The Expansion
Header banks 7A and 8A will be configurable.
These banks (7A & 8A) currently have the DAC SPI and ADF4001/2 SPI
buses. This is okay because the VIH of these parts is 1.4 V, so even a
1.8 V signal should be able to drive it with ease.
- SPI constraints
- TX data constraints
- RX data constraints
Design fails timing primarily due to tx_trigger signals not being
properly synchronized into the tx_clock domain.
There is a second type of timing violation on the LVDS link clock that
seems concerning. Hoping that fixing the previous major violation will
allow the fitter to prioritize these failing nets.
FX3 back to 1.8 V to save power. Using 3.3 V wastes about 1 W when the
interface is going at full speed. There is no need for the adi_rx_clock
to reach two PLLs, one is sufficient.
Not able to get adi_tx_clock to use the dedicated PLL CLKOUT ports on
Bank 5B because the bank does not have enough TX pin pairs for the data
and frame lines. Using regular I/O pin for adi_tx_clock seems okay.
Synthesis and fitting successful.
Reorganized the pinout for optimal PLL usage according to
Figure 4-16 (PLL Locations for Cyclone V E A2 and A4 Devices)
in the Cyclone V Handbook.
This new pinout requires that the FX3 operates at 3.3 V, but doing this
adds some flexibility in the expansion GPIO interface.
Major changes:
- AD9361 LVDS lines are on Banks 7A & 8A. These are 2.5 V
banks (required for the LVDS I/O standard).
- Allows LVDS RX clock (CLK10p,n) access to the top two PLLs.
- Expansion GPIOs, RF switching, and miscellaneous I2C/SPI interfaces
are now on Banks 4A & 5B. These are 3.3 V banks.
- FX3 interfaces on Banks 3A, 3B, and 5A are now 3.3 V (from 1.8 V).
The reason for this is because the predriver voltage rails (VCCPD)
are shared. VCCPD Groups: {1A & 2A}, {3B & 4A}, {7A & 8A}
- Define input clock frequencies
- Change FX3 GPIF interface to 3.3 V
- Add adi_ctrl_out[7:4]
- Add adi_enable
- Small tweaks to signal/port assignments to get rid of warnings